avav在线看_国产性色AV高清在线观看_狠狠干影院樱桃视频整合全网影视:_成人av中文字幕_欧美久久一级_91久久丝袜国产露脸动漫

October 8, 2021

Hot Runner Fundamentals

How melt delivery technology helps minimize waste and increase production efficiencies

 

What is a hot runner system? This is probably the first question for those who are not fully familiar with the injection molding process. Hot runner systems are a critical component of the injection molding process. Since their introduction to the industry, hot runners have continued to play a key role. While hot runners increase the initial cost of a mold, their many production enhancements make them the more economical choice over the long term.?

What is a hot runner?

Hot runners allow for increased productivity and system performance, producing better part aesthetics, greater flexibility and improved process monitoring. In addition, they improve energy efficiency and eliminate scrap plastic, resulting in faster cycle times and reduced part cost. They also deliver melt to the mold with high gate quality, excellent cavity-to-cavity balance, fast color changes, total design freedom and greater customizability. Hot runner solutions help processors achieve the highest levels of quality and part volume at the lowest part cost. And they are available in both hot tip and valve gate configurations, optimized for a processor’s specific application.

Applications with high output and long product life have the most to gain by using hot runner technology, but so do lower cavitation molds where speed and consistency are important to continuous improvement. This article provides an overview of how hot runner melt delivery systems work and how they can improve the injection molding process.

Cold Runner Limitations

During the injection molding process, one of the most important requirements of the mold is to deliver melt from the barrel to the cavity. Melt delivery management has a major impact on final part quality and the ultimate success of the production line. Precise control of resin flow, pressure and temperature is critical. The success of the molding process is directly related to the design of the melt delivery system, so a close examination of a hot runner vs. cold runner solution is helpful.

Cold runners are solidified plastic flow channels found inside molds, and they must be removed from the mold and plastic part after the molding process is completed. Cold runners are the result of channels machined in the mold’s parting surface that provide access for molten resin to flow through the gate and into the cavity. The molten resin cools and hardens and?is ejected with the part,?and the cycle begins again. Cold runner systems typically have little impact on starting mold cost or initial capital expenditure. They are often used in molds designed with short or infrequent production runs and low cavitation.

However, some molded parts generate increased demand and eventually move to higher-cavitation molds. When this happens, a cold runner can have increased impact on processing and its related costs. A larger runner system equates to more resin to inject, cool and handle. Cold runner layouts can be complicated, and cavities must be spaced further apart to accommodate the runner and venting.

Cold runners can be a detriment when it comes to cycle time, since melt is still supplied to the cavity during the pack phase. Cold runners also typically have greater thickness than the part and therefore take the longest time to cool. Clearly, one of the most important considerations is that cold runners are a costly waste of resin. Processors are forced to throw away the runner, recycle it through regrind for use in other processes or sell it as bulk scrap for pennies per pound.

The advantages of a two-plate cold runner mold include compactness, low capital cost and low residence time. It is also simple to maintain, offers rapid color change and has easily machined gates. Among disadvantages are the production of scrap plastic, costly secondary operations for de-gating, extended cycle time, and quality issues including poor surface finish and dimensional stability.

Scrap from a three-plate cold runner system can be reground, but the process creates other issues. Processors are faced with many questions surrounding future use of cold runner regrind in new applications. Does the part require virgin material? Is only a small percentage of regrind allowable? Is there unwanted material in the scrap? Can foreign debris plug gates? Meanwhile, there are numerous de-gating issues such as whether the runners will break off or must be cut off. There is the possible need for manual labor and related capital expenditures for automated de-gating machinery. This investment can be expensive with extended return-on-investment (ROI) ramifications.

Hot Runners Bring Optimization

The alternative melt delivery system is a hot runner. Its function is similar to that of the cold runner, as it provides a path for molten resin to flow through a highly technical and carefully engineered system. The most important difference is that a hot runner never allows molten resin to solidify. The distribution network is completely encased in a steel manifold and never exposed to air.

The manifold distributes molten resin to nozzles?(nozzles are often called “drops”) that?provide access to the gate and cavity. The manifold and nozzles are regulated with thermocouples and heaters to maintain the temperature of the molten plastic. Where a cold runner can be likened to an open-air downtown street, the hot runner is more like a subway tunnel. While a hot runner increases mold price, it should be considered an investment because of its ability to eliminate waste, reduce cycle time and decrease part variation.

The hot runner is often considered one of the most sophisticated systems in the injection molding process. Various materials and their functional capabilities contribute to the overall engineering and final process performance. Several options are available for gate design and temperature control, depending on resin and application. Gates can be controlled thermally with hot-tip nozzles or mechanically with valve-gate nozzles. These have their own design requirements for how they interact with the mold. Temperature controllers can be used for process monitoring, control and fine adjustment. Husky’s own Ultra® hot runners feature Ultra HelixTM valve gates, a technology that delivers a gate vestige so clean, it is virtually unmeasurable.

Hot runners eliminate the need to handle?the cold runner before, during and after processing. Manual labor or robotics are not needed to remove solidified runners or handle regrind, resulting in reduced cost, less equipment to maintain, better use of precious floor space and valuable time savings. With no runners to manage, this eliminates de-gating or facilitating sorting. For processors, these cycle time advantages can translate into significantly increased output.

Clear difference in the cycle time

Here’s another hot runner vs cold runner consideration: While both cold and hot runners go through the same stages of the injection molding process, they influence cycle time in very distinct ways. Cold runners can add cycle time, since melt is still supplied to the cavity during the pack phase. Cold runners typically have a greater thickness than the part and take the longest time to cool for safe handling. In addition, the cold runner’s sprue may require greater open stroke to remove, again adding time to each cycle. While the mold is open, time is needed to remove and clear the runner from the mold, either by gravity or a picker. While the next cycle starts, the cold runner remains.

The clamp opening and closing stroke is reduced with a hot runner system. The part cools quickly and is ready for ejection, versus the cold runner, which must cool before ejection. The hot runner system also has a reduced screw recovery time. The cold runner requires a larger shot size compared to the hot runner, which can use a smaller barrel requiring less energy.

To justify the cost of a hot runner, the overall savings must outweigh the hot runner cost. Various factors must be considered in the cost savings calculation, including part quantities, part weight vs. runner weight, resin cost, machine hourly cost, number of cavities, labor rates and regrind acceptance. Again, Husky Ultra® hot runners feature Ultra HelixTM valve gates, which last for millions of cycles—the best longevity in the industry, significantly reducing machine hourly costs.

There is always a tipping point when processors carefully consider a potential conversion to a hot runner system. For example, consider a 64-cavity cold runner mold with a 14-sec cycle time scheduled to run three shifts a day, seven days a week. With 90% uptime, it will run about 2 million cycles and make about 129.3 million parts annually. A part weight of 2 grams?and cold-runner weight of 192 grams?equates to a total shot weight of 320 grams.

Hot Runners Enhance Quality

In addition to reducing waste and increasing production, hot runners allow greater control over part quality, dimensional accuracy and surface finish. The gate location is no longer limited to the perimeter and can be moved to direct melt flow in a way that better influences critical dimensions or other features affected by filling characteristics. A shorter total flow length may be possible, which can reduce cavity fill pressure requirements and other process elements that impact part warpage. The projected total area and clamp tonnage requirement may also be reduced.

Of all the components and equipment in the injection molding process, the hot runner provides the greatest flexibility in making adjustments that influence individual cavities in a mold. While a cold runner also?can be tuned,?the investigation, adjustment and validation can have a long lead time unless the mold is designed to permit quick removal or replacement of cold runner inserts. Changes are often made by hand, making them iterative and difficult to replace. Reverting to the original state can be time-consuming. Steel can be added by welding but requires refinishing, and material properties may not be as resistant to fatigue.

Injection barrel and machine clamp influences are process-encompassing. Swapping mold cavities requires coolant evacuation and can be mechanically intensive, especially on high-cavitation molds. A hot runner’s nozzle tip can be quickly swapped out, heater position changed or zone temperature adjusted; the effect on overall quality?is almost immediately observed.

Enhanced Design and Aesthetics

Surface quality is another important factor in hot runner vs cold runner. Well-designed hot runner gate placement can result in a more functional part with better surface quality. Since the gate can be relocated to anywhere on the part, runner trimming, secondary operations and their inconsistency can be eliminated.

Enhanced surface quality can be especially important for applications such as irrigation, where the flow of individual drops of water are controlled, and in medical, where the risk of tearing a surgeon’s glove on a gate/trim vestige?must be minimized. Similar performance is required in healthcare, where a catheter must be as unobtrusive as possible. Some iconic packaging and consumer electronic parts known and recognized today would have never been possible without optimal gate design and placement.

Depending on the application, there are many factors that impact the suitable design of the hot runner system. These include gate type (wear, cooling, tolerance and dimensional design), manifold requirements (flow balance, thermal balance, melt channel sizing, mold size and number of cavities) and processing variables (pressure, injection speeds, mold and processing temperatures, resin type, and system timing).

Gating Options Deliver Functionality and Quality

The gate is a tiny restricting feature where plastic enters the cavity. Today, thermal (hot tip) gating and valve gating are the two hot runner options for injection molders. A thermal gate is a simple gating method with no moving parts. The probe is made of copper, a highly conductive material that transfers heat. Static plastic freezes at the gate during hold, creating a membrane/skin that creates a tiny frozen slug to block the gate. The frozen slug is blown out at the start of the injection process. Temperature and position of the hot tip probe are important considerations, and precise machining is necessary.

There can be gate quality issues when thermal gating is employed. Specifically, variation in tip position relative to the gate can impact the gate vestige, sometimes resulting in stringing (angel hair), drooling and even a non-fill part. A clean gate vestige is a competitive edge that Husky designs into its Ultra® hot runners.

The other gating option, valve gating, is a more controlled method that offers higher gate quality. A valve stem actuates to mechanically open or close the gate. Plastic is injected with the valve stem in the “back” position. After hold, the valve stem is actuated forward, mechanically closing the gate. Valve gating offers a wider operating window and greater shot-to-shot consistency compared to thermal gating. The gate diameter is larger, and there is less gate shear and reduced stress in the part. Valve gating also results in no vestige issues.

Valve gating can use two different shutoff methods—conical (taper type) and cylindrical (plunger type). A conical shutoff is used in non-precision applications and requires more strength in the gate area to avoid premature cracking, while the cylindrical shutoff delivers higher gate quality for precision parts by incorporating a tight tolerance slip-fit pin that requires no preload. 

Depending on application requirements, there’s a variety of actuation options for valve-gated hot runner systems. These include hydraulic, pneumatic and electric (servo motor). Valve stems can be moved individually or as a synchronized group with plate actuation. The pneumatic option is the most popular because it is low-cost, cleanroom friendly, and easiest to manage and maintain. 

Manifold requirements also play an important role in initial system design implementation. Hot runner manifolds are available in an unlimited number of custom sizes with flexible drop locations. Manifold shapes and sizes are dependent on the number of mold cavities and spacing. Channel layouts must be balanced to achieve optimal flow conditions. Melt channels have customized sizes depending on the application. Heater profile designs are optimized and validated for every shape and for every resin property.

While most traditional hot runner systems operate at straight angles, there are complex systems that handle more intricate nozzle configurations. Among these options, bolted manifold systems offer varied angled melt delivery for contoured surfaces like headlight bezels. 

Process Controllers Provide Accuracy and Consistency  

Every hot runner system requires a temperature controller to manage temperature and mechanical settings. Husky Altanium® mold controllers provide highly accurate temperature and servo control and are the best fault recovery solutions in the industry. They feature easy-to-use navigation on large full-color touch monitors and are available in a variety of configurations that can be implemented in any injection molding environment.

All Altanium® controllers use Active Reasoning Technology (ART), providing optimized control for greater shot-to-shot and cavity-to-cavity consistency and repeatability. ART delivers tighter control and minimized variability through best-in-class power output delivery, fully isolated thermocouple inputs and industry-leading thermocouple sample rates that ensure the integrity of temperature readings. 

Conclusion: The Importance of Hot Runners 

Hot runner technology has been an invaluable tool in the production of injection-molded parts. It has optimized the molding process with superior melt control and processing performance, yielding higher-quality parts and greater output capability.

Hot runner systems offer significant performance advantages over cold runner systems. Major savings can be achieved through reduced resin usage, cycle time improvements and post-processing elimination. Hot runners can be customized with a variety of engineered solutions configured for a particular application.

The injection molding industry continues to see strong movement in conversion from cold runners to hot runners, along with advances in hot runner technology. Hot runner solutions are positioned to meet new industry challenges as plastic part designs continue to push boundaries, and reduced resin use continues to be a focus for all molders. The expectation is melt-delivery management through sophisticated hot runner technology will play an increasingly critical role in the injection molding process.

主站蜘蛛池模板: 神马国产精品|国产丝袜91久久久久久久久久久|亚洲人成在线播放网站|国产8区|四虎永久在线精品免费网址|近伦毛片中文字幕免费的 | 国产一区二区三区怡红院|91自拍.com|国91精品久久久久9999不卡|久久精品国产精品亚洲艾草网|九色精品|亚洲一区二区综合 | 国产7页|日韩不卡在线播放|国产精品丝袜美女|亚洲人成无码WWW久久久|狼色精品人妻在线视频|亚洲国产一区二区久久久777 | 一级影片在线观看|亚洲精品久久久久9999吃药|免费毛片wwwcomcn|91一级片|超碰人人精品|GOGO亚洲肉体艺术 | 成午夜精品一区二区三区软件|精品亚洲第一|大地资源二在线视频观看|国产美女视频黄=a视频免费|亚洲国产成人=aV片在线播放|日本乱偷人妻中文字幕在线 | 中国一级毛片在线视频|99在线观看免费视频|亚洲九九热|www.精品国产|亚洲www久久久|欧美白浆视频 | CONDOM色孩交VIDEOS精品|#NAME?|四虎永久在线精品8848=a|三级在线观看国产|日韩久久成人|大学生一级一片第一次野外 | 高清偷自拍第1页|午夜精品久久久久久久爽|黄色影院网站|国产午夜无码片在线观看影院|性一交一乱一乱一视频96|久热精品在线观看视频 | 久草国产精品视频|综合日韩天天久久一本|精品国产性色无码=av网站|国产极品福利在线|国产精品白丝喷水JK娇喘视频|免费xxxxx在线观看网站软件 色综合久久综合中文综合网|午夜福利国产在线观看1|毛片免费视频观看|黑人把女人弄到高潮视频|www.国产精品视频|免费色网 久久网国产|国产精品久99|国产hsck在线亚洲|性导航唐人社区|久久精品国产亚洲=aV高清色欲|久久99精品久久久久久久夜夜爽 | 中国黄色影院|99精品一区二区三区|久久成人久久|疯狂做受XXXX高潮吃奶|欧洲精品二区|激情超碰在线 | 宝贝扒开下面自慰给我看|单亲乱l仑视频在线观看|久久久国产一区二区三区|激情久久久久久久久|久久国产精品久久精|国产三级在线免费 | 一级国产性感片|国产一区二区三区免费观看网站上|日韩欧美亚洲天堂|亚洲无码在线观看色网视频|亚洲国产午夜精品理论片|天天干伊人 | 老司机67194精品线观看|激情久久久|九九热视频在线播放|乱人伦人妻精品一区二区|欧美一区二区三区影视|日本高清不卡在线观看 | 1000部禁又爽又黄的禁片免费|一区二区三区在线免费视频|国产精国产精品|中文字幕人妻系列人妻有码|在线日韩免费|男女wwww | 在线观看免费黄网|久久久久久久久久久鸭|91社影院|日本一区免费网站|尹人香蕉久久99天天拍|任我爽橹在线精品视频 | 亚洲=aV永久综合在线观看另类|#NAME?|日本亚洲精品成人欧美一区|久草精品在线播放|国产亚洲综合视频|亚洲精彩视频在线 | 国产人成精品香港三级在线|国产乱人伦偷精品视频免观看|男女无套免费视频软件|中文无码一区二区不卡αv|91短视频免费|亚洲美女精品区人人人人 | 国产精品成人**免费视频|亚洲免费在线播放视频|国产激情一级毛片久久久|99久免费精品视频在线观78|97dyy97影院理论片在线|日韩成人免费视频 | 国产大学生粉嫩无套流白浆|老司机久久99久久精品播放免费|日本国产三级|久久久久久久久久久久久久久久久久=av|欧美日本精品|涩涩91 | 午夜无码伦费影视在线观看|在线看成人片|免费在线观看黄色=av|#NAME?|日韩=a∨精品日韩在线观看|精品人妻无码一区二区色欲产成人 | 国产在线xxx|夜夜摸夜夜添夜夜添破|老老熟妇XxXXHD|91国内视频|国产一二级片|久久公开免费视频 | 激情综合欧美|日本一区欧美|97色伦欧美一区二区日韩|国产东北女人做受=av|又色又爽又黄又粗暴的小说|中文字幕无码日韩欧毛 | 少妇天天干|一本久道久久综合中文字幕|色哟哟国产成人精品免费|国产主播户外勾搭人xx|精品无人区无码乱码毛片国产|亚洲欧美中日精品高清一区二区 | 99热久只有|九一免费视频|中日韩无砖码一线二线|日韩免费成人=av|国产在线中文字幕|国产=aV麻豆M=aG剧集 | 天天操天天爱天天干|日本中文字幕免费在线观看|国产精品久久毛片=a片软件爽爽|国产精品色=av|中文字幕第二十一页|日本护士大口吞精视频网站 | 亚洲另类在线视频|6精品国产乱码久久久久久|欧美黄色=av|日本高清视频网址|草草网站影院白丝内射|成人免费=a级毛片无码片 HD性丰满白嫩白嫩少妇=aV|免费成人黄色大片|久久精品中文字幕|久久无码国产专区精品|欧美=a∨|91精品一久久香蕉国产线看观看软件 | 少妇放荡白洁干柴烈火40视频|一级=a=a=a=a毛片|国产黄色大全|#NAME?|亚洲成在人线综合导航|国产精品黄在线观看 | 阿v天堂2018在无码免费|男人添女人下身视频网站|日韩精品久久久久久免费|日韩爱爱免费视频|视频在线精品一区|成人欧美一区二区三区视频xxx | 冥王星之恋泰剧在线观看|国产亚洲精品=a片久久久|日韩大片免费在线观看|免费无码=aV片在线观看网址|最新精品国偷自产在线|国产偷人激情视频在线观看 | 日本性爱视频在线观看|欧美日韩xxx|国产女人高潮大叫特级毛片|#NAME?|www.亚洲一区二区三区|男女羞羞网站 | 青青草手机视频在线|天天看天天草|新久草视频|中文字幕在线亚洲三区|国产成人啪精品视频免费网|国产精品原创=aV片国产安全 | 成人极品影院|久久综合亚洲色hezyo国|www.在线视频|奇米777四色精品综合影院|土壤污染状况调查|人人草人人插 | www欧美精品|成全在线观看免费高清动漫|富婆推油偷高潮叫嗷嗷叫|久久做受WWW|韩国羞羞|日韩亚洲欧美中文三级 | 国产精品免费久久|国产老妇人成视频在线播放播|国产精品xxxxx|亚洲精品久久视频|啊轻点灬大JI巴太粗熟妇|2021年国产精品免费 | きょこんきょうしゃ在线|91狠狠爱|亚洲=aV日韩综合一区尤物|丝袜亚洲另类欧美变态|GOGOGO高清在线观看|亚洲=aV成人无码精品综合网站 | 天天爽天天草|久久成人一区二区|国语对白露脸XXXXXX|黄色片视频在线免费观看|川上优在线|中国黄色免费 | www.97色.com|免费看日韩|永久黄网站色视频免费看|人妻日韩视频一区二区|亚洲黄视频|wwwwxxxx美国 | 日日爽天天操|亚洲=aV永久无码精品一区二区|免费精品视频在线观看|日本高清色视频www·com|国产成人麻豆免费观看|色一情一区二 | 中国极品少妇xxxxx小艳|久久国产日韩|九七=av|欧美一级淫片免费看|少妇搡BBBB搡BBBB毛多多|无码人妻一区二区三区巨免费 | 影音先锋99|成年女人免费大片视频|天天色草|特黄=a=a级毛片免费视频播放|3级片免费|在线观看中文字幕视频 | 91精品国产一区二区三区四区在线|午夜大尺度福利视频|eeuss亚洲精品久久|#NAME?|一品色堂|性一交一乱一伦一色一情丿按摩 |